Residential · Orlando, FL
When a steel or aluminum fence starts leaning, rattling, or cracking at the welds, a quick patch usually fails. Titan Mobile Welding Orlando has served Orlando since 2016 with on-site metal fence repair that restores strength, alignment, and clean function.
A durable metal fence repair starts with proper prep and a stable base. We inspect posts, rails, pickets, hinges, and latches for cracked welds, bent tubing, corrosion, and movement at the footing, then square and brace the panel to bring it back to plumb. Broken joints are cleaned to bright metal with a grinder and flap disc, old paint is stripped back to sound steel, and gaps are fitted tight so the weld penetrates instead of bridging. Depending on the fence and access, we use MIG (GMAW) with ER70S-6 wire for carbon steel or TIG (GTAW) for precise aluminum work, then add fishplates, sleeves, or gussets where a simple re-weld would re-crack.
Central Florida moisture and irrigation overspray accelerate rust at the bottom rail, post bases, and heat-affected zones around old welds. After welding, we treat exposed steel with rust-inhibitive primer and match-coat with an exterior enamel or direct-to-metal coating, and we can recommend galvanizing repair spray for light-touch protection on zinc-coated parts. For aluminum fences, we clean and prep for an epoxy primer and topcoat to prevent filiform corrosion and keep the finish consistent. If a post is loose at grade, we can reset or reinforce it, improve drainage around the base, and seal openings in tubing to reduce water intrusion that causes internal rust and swelling.
Orlando property owners choose us because we bring the shop to your gate and solve the root cause, not just the visible crack. Our mobile rig is set up with welding power, shielding gas, grinders, clamps, and layout tools so we can cut out failed sections, fabricate replacement pickets or rails, and weld in new steel on the spot. You get practical options, from a budget-friendly weld repair to a heavier reinforcement using thicker-wall square tube or angle, with clear tradeoffs on longevity and appearance. We keep the site controlled with spark protection and careful heat management around wood, vinyl, landscaping, and powder-coated panels to avoid collateral damage.
Before we leave, we do a full walkthrough: gate swing, latch alignment, hinge pin wear, ground clearance, and panel straightness from end to end. We clean the weld area, blend spatter, confirm there are no sharp edges, and touch up coatings so the repair looks intentional, not patched. You receive a written estimate up front, straightforward scope notes on what was repaired or replaced, and recommendations for maintenance like repaint intervals and rust monitoring points. If your fence has multiple problem spots, we can prioritize safety-critical sections first and plan phased repairs to fit your budget and timeline.
Yes. We provide a free written estimate with the scope, materials, and what is included for welding, reinforcement, and finishing.
Often, yes. Many mobile setups can run independently; if shore power is needed for a specific job, we will confirm requirements during scheduling.
We commonly weld carbon steel, stainless steel, and aluminum, selecting MIG, TIG, or stick based on thickness, access, and service conditions.
Yes, for many field repairs and reinforcements such as cracked members, damaged connections, added plates, and fabricated brackets. We evaluate access, load paths, and safe repair options before welding.
Scheduling depends on job size and parts availability. Call with photos and a brief description and we will offer the next available window and any same-week options.
Metal fence repair is usually needed when welds crack, posts shift, gates sag, or rust eats through thin tubing. In Orlando, Titan Mobile Welding Orlando handles on-site welding repairs for steel and aluminum fences, gates, and rail sections, restoring strength and smooth operation without the delay of removing panels and hauling them to a shop. Our process focuses on structural fit-up, full-penetration welds where possible, and protective coatings that stand up to year-round humidity.
Common calls include split welds at hinge plates, cracked joints where rails meet posts, broken pickets from impacts, and bottom-rail rust at grade. We start by measuring and bracing so the fence goes back to plumb, then grind to clean metal, remove failed welds, and refit parts with tight joints. When metal is too thin or corroded to hold a reliable weld, we cut out the damaged section and weld in new material, typically mild steel square tube or flat bar, matched to the original wall thickness when possible.
Because many fences are painted, powder-coated, or partially galvanized, we plan the repair around finish protection. Heat is controlled to limit burn-back, then we smooth and prep for primer and topcoat so the repaired area blends and resists flash rust. For gates, we also correct latch and hinge geometry so the repair does not bind or drag, and we can add stops or reinforcement plates to prevent repeat failures.
If you need metal fence repair for a residential perimeter, pool gate, equipment enclosure, or commercial security fence, we can evaluate what can be welded, what should be replaced, and what reinforcement will extend service life. Share a few photos and measurements, and we will provide a clear plan and a written price range to get your fence secure and functioning again.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Orlando. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
