Commercial · Orlando, FL
When a beam, column, or connection starts cracking, rusting through, or pulling out of alignment, structural steel welding needs to be done correctly and safely. Titan Mobile Welding Orlando has served Orlando since 2016, providing on-site structural steel welding repair for residential and commercial steel that has to carry real loads.
Every structural steel welding repair starts with evaluation and prep. We identify the member type (I-beam, channel, angle, tube steel), the failure point (crack at weld toe, torn base metal, bent flange, elongated bolt holes), and what caused it (impact, corrosion, fatigue, poor fit-up). Then we set safe access, confirm measurements, and prep the joint with grinding, carbon-arc gouging when needed, and proper bevels for full penetration or partial joint penetration welds. If reinforcement is required, we fabricate and fit plates, gussets, stiffeners, or splice plates from A36 or A500 steel, using clamps, strongbacks, and temporary bracing to hold alignment before welding.
Field conditions matter, especially on exterior steel and older painted members. We control heat input and distortion, remove coatings near the weld area, and address moisture and wind so shielding gas and weld quality stay consistent. Depending on the joint and access, we use MIG (GMAW) or stick (SMAW) with common structural electrodes like E7018, selecting the process for penetration, positional welding (vertical, overhead), and reliability. After welding, we clean, blend, and verify tie-in, then apply a practical finish like primer, rust-inhibitive coating, or weld-through primer for areas that will be top-coated later. If the repair ties into concrete or masonry, we coordinate hole layout and edge distances for anchors and base plates so the load path makes sense.
Orlando customers choose us because we show up ready to solve real structural problems without dragging steel to a shop. You get a licensed and insured mobile welder who can cut, fit, weld, and reinforce on-site with professional equipment, including generators, welding machines, grinders, mag drills, and steel fabrication tools. We communicate clearly about what we see, what we recommend, and what is repairable versus what should be replaced. Work is performed with practical structural welding methods aligned with AWS D1.1 expectations for workmanship, fit-up, and sound weld profiles.
Before we leave, we walk you through the repair and what it changes structurally. You receive a clear scope, a free written estimate up front, and photos when helpful for property records, facility managers, or insurance documentation. If additional steel is needed, we can return with pre-cut parts or fabricate on-site depending on access and tolerance needs. The goal is a safe, serviceable repair that restores strength at the connection, reduces future cracking, and leaves steel protected from Florida humidity.
Yes. We provide a free written estimate with the scope, materials, and what is included for welding, reinforcement, and finishing.
Often, yes. Many mobile setups can run independently; if shore power is needed for a specific job, we will confirm requirements during scheduling.
We commonly weld carbon steel, stainless steel, and aluminum, selecting MIG, TIG, or stick based on thickness, access, and service conditions.
Yes, for many field repairs and reinforcements such as cracked members, damaged connections, added plates, and fabricated brackets. We evaluate access, load paths, and safe repair options before welding.
Scheduling depends on job size and parts availability. Call with photos and a brief description and we will offer the next available window and any same-week options.
Structural steel welding is often the fastest way to restore strength when a beam, column, or connection has cracked, corroded, or shifted out of alignment. Titan Mobile Welding Orlando performs on-site structural steel welding repair for residential and commercial properties, focusing on safe prep, correct joint design, and durable reinforcement so the steel can carry load again with confidence.
Common calls for structural steel welding include cracked welds on stair stringers, mezzanine framing, equipment supports, trailer and container frames, storefront steel, carport posts, and damaged base plates. We start by confirming the failure mode and the load path, then prep the joint properly. That can mean grinding to bright metal, beveling for penetration, removing old weld with carbon-arc gouging, and fitting reinforcement like fish plates, doubler plates, or gussets. We routinely work with structural carbon steels such as A36 plate and A500 tube, and we select a welding process that matches access and position, including SMAW with E7018 or GMAW where shielding and fit-up allow.
Field welding also has to account for distortion and finish. We use clamps, temporary bracing, and controlled weld sequences to keep members straight and connections tight. After welding, we clean spatter, blend transitions, and address corrosion protection with primer or rust-inhibitive coatings when requested. For bolted connections that have wallowed holes or torn material, we can build back steel and re-drill, or install reinforcement plates to restore bearing area, depending on the situation.
If you need structural steel welding in Orlando, we make it straightforward. Share photos and measurements if available, and we will provide a free written estimate and a practical repair plan. Once scheduled, we arrive with the tools to cut, fit, weld, and finish on-site so your steel is repaired with minimal downtime.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Orlando. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
