Residential · Orlando, FL
Aluminum cracks and broken brackets get worse fast, especially on gates, trailers, marine parts, and equipment frames. Titan Mobile Welding Orlando brings mobile aluminum welding to your site in Orlando with clean, controlled TIG and spool-gun MIG repairs that fit and function like the original part.
Good aluminum repair starts with prep and correct base metal identification. We check thickness, alloy type when possible (common 5xxx and 6xxx series), joint design, and whether the part is cast or extruded, then set up for TIG (GTAW) or MIG with a spool gun. Before striking an arc we remove paint, anodizing, and oxidation, mechanically clean with dedicated stainless brushes, and degrease with acetone to prevent porosity. We also verify fit-up, clamp alignment, and decide on filler selection such as ER4043 or ER5356 based on the application and service conditions.
Florida heat, humidity, and salt air accelerate corrosion and can hide contamination in pits and seams, so we take extra time on cleaning and preheating when needed. Our process controls heat input to limit warping on thin sheet, tube, and angle, and we can stitch-weld or back-step to keep parts straight. After welding, we blend and dress welds as requested, then recommend a finish that matches the job, from scotch-brite and polish work to primer and paint compatibility, or leaving a clean bare weld when the part will be powder-coated or anodized later.
Orlando customers choose us because aluminum is not a one-setting-fits-all metal, and we treat it that way. You get on-site capability for repairs that are tough to transport, from trailer ramps and boat-lift parts to handrails, fence panels, and equipment guards. We show up with the right setup, including a dedicated aluminum wire system, argon shielding gas, proper torch consumables, and the measuring and fixturing tools needed to keep holes, hinges, and mounting points in spec. Titan Mobile Welding Orlando is licensed and insured, serving since 2016, with clear communication and a written estimate before work starts.
To close out the job, we walk you through the repair, confirm clearances and moving parts, and check weld coverage, tie-in, and alignment. If the part is load-bearing, we discuss realistic use limits, any reinforcement options (gussets, doubler plates, sleeve repairs), and what to watch for over time. You receive a straightforward scope of work, photos when helpful, and cleanup of the work area, plus guidance on coating, galvanic corrosion prevention (isolators between aluminum and steel), and maintenance so the repair lasts.
Yes. We provide a free written estimate with the scope, materials, and what is included for welding, reinforcement, and finishing.
Often, yes. Many mobile setups can run independently; if shore power is needed for a specific job, we will confirm requirements during scheduling.
We commonly weld carbon steel, stainless steel, and aluminum, selecting MIG, TIG, or stick based on thickness, access, and service conditions.
Yes, for many field repairs and reinforcements such as cracked members, damaged connections, added plates, and fabricated brackets. We evaluate access, load paths, and safe repair options before welding.
Scheduling depends on job size and parts availability. Call with photos and a brief description and we will offer the next available window and any same-week options.
When aluminum breaks, you need a process that controls contamination and heat, not a quick patch. Titan Mobile Welding Orlando provides mobile aluminum welding for homeowners, contractors, and facility managers who need on-site repair of aluminum gates, railings, trailers, boat and dock hardware, equipment frames, and custom fabricated parts. We bring the welding rig to you, evaluate the base material and joint design, and complete clean TIG (GTAW) or spool-gun MIG repairs that restore strength, fit, and function.
Mobile aluminum welding is ideal when the part is bolted in place, oversized, or tied into other structures. Instead of disassembling a gate or hauling a trailer to a shop, we diagnose the failure at the source, confirm alignment, and set up safe work zones. Our prep focuses on oxide removal and degreasing, because aluminum oxide melts at a much higher temperature than the base metal and can trap contamination. Depending on thickness and access, we use TIG for precise control on thinner material and detailed work, or a spool gun MIG setup for efficient production-style repairs.
Common calls include cracked welds at hinges, broken tabs and brackets, fatigued trailer ramp corners, and corrosion damage around fasteners. We can reinforce weak areas with gussets or doubler plates, rework misaligned holes, and address galvanic corrosion risks by isolating aluminum from steel where practical. If a part is cast aluminum, we inspect for porosity and prior repairs and discuss whether welding is the best option or if replacement is safer.
If you are searching for mobile aluminum welding in Orlando, the goal is a repair that holds up in real use, not just looks good on day one. We provide a written estimate, explain the welding method and filler choice, and finish with a final fit and function check. Call Titan Mobile Welding Orlando to schedule an on-site evaluation and get a free written estimate.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Orlando. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
